Shanghai Kosta Electric Co., Ltd.
Shanghai Kosta Electric Co., Ltd.
홈페이지> 블로그> Diesel generator set basic commissioning steps

Diesel generator set basic commissioning steps

March 23, 2023
Diesel generator set basic commissioning steps
The first step is to add water to the tank. Turn off the drain valve first, add clean drinking water or purified water to the position of the tank opening, and cover the tank lid.
Second, add oil. Select CD-40 Great Wall brand diesel engine oil. Oil is divided into summer and winter. Different oils are used in different seasons. Pay attention to the vernier in the process of adding oil, until the oil is added to the vernier scale, fill the oil cover, and do not add too much. Excessive oil can cause engine oil and burning of oil.
The third step, the machine's oil and return to distinguish. In order to ensure that the machine's oil intake is clean, diesel is generally allowed to settle for 72 hours. Do not insert the oil into the bottom of the cylinder so as not to suck dirty oil and block the tubing.
The fourth step, pump diesel, first loosen the nut on the hand pump, holding the handle of the diesel generator hand pump. Pull evenly until the oil enters the oil pump.
The fifth step is to release air. Want to loosen the bleed screw of the high-pressure pump, then hand pressure hand pump, you will see the oil hole and air bubbles overflow in the screw hole, until you see the outflow of all oil. Tighten the screws.
In the sixth step, start the motor. Distinguish the positive and negative poles of the motor from the positive and negative poles of the battery. This is the positive pole and in the tail this is the negative pole. Between the two batteries should be in series, can reach the effect of 24V. Connect the positive pole of the motor first. When connecting to the positive pole, do not allow the terminals to contact other wiring sections. Then connect the negative pole of the motor, be sure to connect firmly, in order to avoid sparking and burning the wiring section.
The seventh step, air switch. Before the machine is not started or the machine does not enter the power transmission state, the switch should be in a separate state. There are four terminals at the lower end of the switch. These three are three-phase live wires, and the Ito generator set is connected to the power line, and the independent side is zero. The line, the neutral line and any one of the fire lines in contact with the power is 220V lighting power, do not use a third of the rated power of the generator.
The eighth step, the meter section. The ammeter, during use, accurately reads the power used. Voltmeter, detects the motor output voltage. Frequency table, frequency table must reach 50Hz, is the basis for detecting the speed. Current and voltage switches to detect motor meter data. The oil pressure gauge detects the running oil pressure of the diesel engine. At full speed, the pressure should not be less than 0.2 atm. The tachometer should have a speed of 1500 rpm. The water temperature meter cannot exceed 95 degrees during use, and the oil temperature cannot exceed 85 degrees.
The ninth step, start. Now operate it again, turn on the ignition switch, press the button, release the Volvo generator set after the vehicle is in motion, run for 30 seconds, and toggle the high and low speed switch. The machine will slowly increase to high speed at idle speed and check the readings of all the instruments. Under all normal conditions before the switch on the air, a successful transmission, wire
The tenth step, parking. Turn off the air switch first, cut off the power supply, and adjust the diesel engine from high speed to low speed. Allow the machine to idle for another 3 to 5 minutes before closing it.
1, diesel generator
The main rotor that drives the electric ball rotates, causing the electric ball's stator output current.
2, electric ball
The Ito diesel generator generates AC power.
3, electrical control system
Control the rotational speed of the diesel generator and stabilize the voltage.
4, water tank
The internal stability of the generator is cooled to stabilize the stability of the machine.
5, the chassis of the generator set

Connect all the components of the generator. And ensure stable operation of the generator set

Perkins Diesel Generator

문의하기

Author:

Ms. Michelle

Phone/WhatsApp:

+8618705258272

인기 상품
You may also like
Related Categories

이 업체에게 이메일로 보내기

제목:
이메일:
메시지:

Your message must be betwwen 20-8000 characters

문의하기

Author:

Ms. Michelle

Phone/WhatsApp:

+8618705258272

인기 상품
Blog News
Diesel generator set

October 11, 2023

Small Power Generator

August 28, 2023

We will contact you immediately

Fill in more information so that we can get in touch with you faster

Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.

송신